PCI Online is a unique training package for the protective coatings industry. The training programme has been specifically developed for personnel who have an interest in surface treatment and corrosion control with the use of protective coatings.
Within the training modules you will find following International Standards and references used in the coatings industry.
The use of illustrations from the above organisations and standards is for training purposes only.
When conducting inspection duties always ensure you use the exact document or standards which will contain the full contents of the standard along with the quality images needed to use the standard or document.
All courses, course materials, and related services provided under this agreement are provided on an “as is” and “as available” basis.
SSPC disclaims all warranties, express or implied, oral or written, including implied warranties of merchantability, fitness for a particular purpose, title, and noninfringement, and any warranties from course of dealing, usage or trade practice.
The affiliate or registered company agrees that industry practices change periodically and that SSPC does not assume any liability or obligation for any failure to update information or the affiliates or registered companies use or misuse of any information presented as part of the course materials.
In the event any software is provided under this agreement as part of the course materials, SSPC does not warrant that the software will be free from interruptions or delays, is compatible with the affiliate or registered company operating environment or mobile device, or is free from malware, viruses, or harmful code.
The software may display or make available third party content which may be subject to additional terms and conditions. The affiliate or registered company acknowledges and agrees that SSPC is not responsible for third party content and SSPC does not assume any liability for your use of third party content.
Please check that the website address you entered is correct as we host several training sites that use similar web addresses
If you have forgotten your password, enter the email address you registered with below then press 'Reset'. This will reset your password and email it to you
All rights reserved. No part of the training material may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of Fitz-Coatings Limited.
Fitz-Coatings Limited, East Farm, Monkton Village, Jarrow, Tyne and Wear, NE32 5NN, United Kingdom.
The Industrial Coatings Applicator is a multi-disciplined task theat covers an enourmous amount of possible activities. This training course has been developed from basic principals to allow a new recruit entrance into the industry, training for an experienced person, and education to lead hands, engineers and assistants or third party personell. The training has been structured so that it can be completed step-by-step from the first unit to the last.
Six training modules have been developed all with a number of individual units.
A considerable amount of effort has been put into the health and safety unit and this is by far the most important module
This first module contains fourteen units and guides the user on a step-by-step basis through the somewhat complex aspect of health and safety.
The first unit wihin, is the generic 'company induction' unit. As each company's activities are wide ranging, this unit offers general guidelines on what an induction should contain.
It is widely accepted that the degree of surface preparation and level of cleanliness have a major bearing on the performance of a coating system.
Abrasive blast cleaning is by far the most efficiant and effective method of surface preparation.
This training course covers all aspects of surface preparation with the use of abrasive blast cleaning.
Six training modules have been developed with a number of units in each module.
Considerable emphasis is put on the health and safety, which compliments the health and safety in the Protective Coatings Application Training Course.
Within the Protective Coatings Application training you will find training units on basic paint application such as brush and roller application.
This training course was designed specifically for coating application with the use of airless spray equipment.
There is a section which covers air assisted conventional spray application, however the majority of industrial and marine coatings are applied by airless spray
Considerable emphasis is put on the health and safety which compliments the health and safety units in the industial coatings applicator and abrasive blast cleaning courses.
Within the site you will find training units for Protective Coatings Application, Abrasive Blast Cleaning and Spray Painting.
This section contains Specialist Modules and any additional units that have not been covered within the three main training courses.
To recognize how fire protection in the form of thin-film intumescent paint is used on structural steel.